ve Transfer Switch 10kva, 1ph, 200-250Vac

The victron MultiPlus C 12/1200/35 (MPN CMP128010000) is a combination of 12V 700W inverter and battery charger. The integrated battery charger provides 35A which allows quick charging even for bigger batteries as long as there is a grid connection.The 12V sine inverter converts your DC battery current into a 230V AC current. Thanks to a pure sine wave this inverter is also suitable for sensitive electronic devices. Versatile and flexibleBesides inverter and charger the MulitPlus also contains a 16A transfer switch which makes it ideal for caravans, campers, boats, yachts and uninterrupted power supply in case of grid fluctuations or blackouts.Moreover it is a handy tool for any grid-tied system which only drains power from the supplier when the battery current is not sufficient. Important features: 700W constant output and 1400W peak current, for 12V battery voltage combination of inverter with transfer switch and 35A battery charger provides pure sine wave at 50Hz VE.Bus communication port allows extensive possibilities in terms of connection, configuration and controlling of Victron MultiPlus devices supports three-phase operation (3 units of the same model needed) supports parallel operation - up to 6 units can be connected parallely to increase system power if needed 2x AC-outputs (Multiplus 3000 and bigger) - on the second output consumers can be connected that should only run when grid-power is available PowerControl-function allows operation with limited generator performance as well as supply through limited shore or grid power PowerAssist-function allows a 'performance-increase' of generators and supports shore power connection if needed usable as UPS-solution (uninterrupted power supply) usable for grid-tied systems which only drain power from the supplier when the battery current is not sufficient or other programmable events have happened compatible with many Victron control- and monitoring-panels three-phase operation with other MultiPlus inverters of identical model possible Massive performance extensionBesides parallel operation three inverters of the same model can be configured for three-phase operation. But there is more: It is possible to connecte 6 x three-phase systems parallely to generate a massive inverter performance of 75kW / 90kVA and a charging capacity of 2000A (when using the 5000 model) PowerControl - operation with limited generator performance, shore or grid powerThe MultiPlus is a powerful battery charger which drains a lot of power (nearly 10A/5kVA Multi at 230V AC) from the generator or grid. With help of the MultiControl panel you can adjust the max. power drained from the generator or grid. The MultiPlus then priors other connected AC-consumers and uses only the "surplus" of energy for charging.This protects the generator or grid from an overload. PowerAssist - performance-increase of generators and shore power connectionWith this function PowerControl is put to a new dimension by enabling the MultiPlus to support small-dimensioned power sources. Load-peaks often occure only within limited periods. In this case the MultiPlus ensures that weak shore- or generator power is compensated instantly through battery power. BackUp-System: AC-power also during blackoutsThe MultiPlus can be integrated in off-grid systems, grid-tied PV-systems and systems using alternative energy sources. A software that detects blackouts and grid failures is also available. Easy configurationIf setting of a device have to be changed this can be done with help of a DIP-switch within minutes.Parallel-connected and three-phase systems can be configured via VE.Bus QuickConfigure and VE.Bus System Configurator software. Monitoring and controlling on siteThere are several option: battery protector, Multi Control panel, VE.Net Blue Power panel, Color Control Panel, smartphone or tablet (Bluetooth Smart), notebook or computer (USB or RS232). Remote monitoring and controllingVictron Ethernet Remote, Victron Global Remote and the Color Control Panel allow remote maintenance and monitoring of the Multiplus. Addiationally system data can be saved for free on the VRM (Victron Remote Management) website. Remote configurationIf the system is connected to the ethernet via the ColorControl-panel you are able to change settings remotely. Delivery scope:1x Victron CMP128010000 Multiplus C 12/800/35 Combination of 12V 700W sine inverter and 12V 35A battery charger1x Manual  

The new MultiPlus 24/800/16-16 (Victron Energy, pmp241800000) is the successor to the Multiplus Compact 24/800. This unit is an advanced device combination consisting of a powerful pure sine wave inverter, an advanced 16a battery charger utilizing adaptive charging technology, and a 16a high speed AC transfer switch. In the event of a mains fault or, if shore power or on-board generator is interrupted, the multi's inverter is automatically switched on and takes over the supply to the connected loads. The switching occurs so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic equipment is guaranteed. main features of the MultiPlus 24/800/16-16 Cont. Output power at 25°c: 700w / 800w at non-linear load Victron Energy mpn: pmp241800000 for 24v system voltage integrated 16a mains charger for your batteries integrated 16a mains transfer switch USV operation possible Extensive accessories available Can be used in numerous applications, whether on land or mobile proven reliability The complete bridging additionally with a ring transformer topology has proven itself for years. The inverter is short-circuit proof and protected against overheating (whether caused by overload or ambient temperature) PowerControl - (Multiplus 800va 1200va only) The Multi Control remote control panel can be used to set the maximum mains or generator current to be drawn. The MultiPlus then takes into account other connected AC loads and uses only the current that is "left over" for charging. This prevents the generator or shore power connection from being overloaded PowerAssist - (Multiplus 800va 1200va only) Load peaks often only occur for a limited period of time. In such a case, the MultiPlus ensures that insufficient shore power or generator power is immediately compensated by energy from the battery. If the load is reduced, i.e. if consumers are switched off, the energy that is then sufficiently available again can be used to charge the batteries High switch-on power This is required for switching on loads with high inrush currents, such as voltage converters for LED lamps, halogen lamps or power tools Search mode When the search mode is set to 'on', the power consumption of the inverter is reduced by approximately 70% during no-load operation. In this mode, when operating in inverter mode, the Multi will turn off at zero load or low load and turn back on every two seconds for a short period of time. if the output current exceeds a set limit, the inverter resumes operation. If this is not the case, the inverter switches off again programmable relay In the basic setting, the multifunction relay acts as an alarm relay, i.e. it switches off the device in the event of faults (device becomes too hot, ripple voltage at the input too high, battery voltage too low) Scope of delivery: Victron Energy pmp241800000, MultiPlus 24/800/16-16

The Multiplus-II 48/5000/70-50 is a high-end device combination by Victron Energy (mpn: pmp482505010) that combines classic Multiplus components with an external current sensor and integrated anti-islanding function. This extends the PowerControl and Powerassist functions to 100 a and expands the potential range of use to ess applications. The inverter module delivers a whopping 5000 w at non-linear load, or 4000 w at linear continuous load. the 48 v battery charger is also very well proportioned, with 70 a charging power, and is complemented by a 50 a transfer switch that allows lightning-fast switching between aC connections important features of the Multiplus-II 48/5000/70-50 PowerControl and Powerassist -increase in mains or generator output built-in anti-islanding function and connection possibility for external current sensor (optional) can be used as a backup device in grid-connected systems for power supply in case of grid failures can be used in various ess (Energy Storage System) applications best suited for professional seafaring, yachts, vehicles and land-based, off-grid applications vE.Bus interface for parallel and three-phase operation, remote monitoring and system integration virtually unlimited power through parallel and three-phase operation can be configured on-site or remotely using vEConfigure software* technical features 5000 w power at non-linear load 4000 w continuous load and 9000 w peak power for 48 v battery voltage, 50 a transfer switch and 70 a battery charger output voltage: 230 vaC, frequency: 50 Hz max. efficiency is 95%, protection class IP22 always enough power thanks to PowerControl and Powerassist a maximum mains or generator current can be set on the Multiplus-II 48/5000/70-50. The MultiPlus-II then takes into account other connected AC consumers and only uses the current that is "left over" to charge the battery. This prevents the generator or mains connection from being overloaded (PowerControl function). The Powerassist function adds a new dimension to the PowerControl principle. Load peaks often only occur for a limited period of time. In such a case, the MultiPlus-II immediately compensates for insufficient generator, shore power or mains power with energy from the battery. if the load is reduced, i.e. if consumers are switched off, the energy that is then available again in sufficient quantities can be used to charge the batteries Solar power: alternating current even in the event of a power failure The device can be used with both non-grid-connected and grid-connected pv systems, as well as with other alternative energy systems. It can be used with both solar charge controllers and grid-connected inverters. maximum flexibility thanks to two AC outputs The main output ensures uninterrupted operation. In the event of a grid failure or interruption of the shore/generator power, the MultiPlus-II takes over the supply of the connected consumers. Switching occurs so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic equipment is guaranteed. The second output supplies power only when AC power is available at the input of the MultiPlus-II. consumers that must not discharge the battery, such as a water heater, can be connected to this output. many possibilities for system expansion Settings can be changed in minutes using the vEConfigure software (which requires a computer or laptop and an MK3 USB interface).several monitoring and control options are available: Color Control gx, venus gx, Octo gx, CaNvu gx, laptop, computer, Bluetooth (with the optional vE.Bus Smart Dongle), battery monitor, Digital Multi control panel Remote configuration and monitoring Install a Color Control gx or other gx products to connect to the Internet. Operating data can be stored and viewed free of charge on our vRM (victron Remote Management) website. If systems are connected to the Internet, they can be accessed remotely and settings can be changed. Scope of delivery: 1x victron pmp482505010 Multiplus-II 48/5000/70-50a 1x user manual

The Multiplus 12/2000/80-32 from Victron (mpn pmp122200000) is a device combination of 12v 2000w sine wave inverter and battery charger. The integrated battery charger has an output of 80a, which means that even large batteries can be fully charged quickly if shore power is available. The 12v sine wave voltage converter built into the Multiplus converts your current from the battery to 230v AC. Thanks to the true sine wave, the power quality is perfect even for sensitive electronic devices. In addition to the two integrated device types, a lightning-fast 32a transfer switch is also built in, which can also be used to implement numerous grid-connected solutions. For system integration, the MultiPlus has a VE.Bus port, which enables virtually unlimited networking. Comprehensive and flexible use Since it has a lightning-fast 32a transfer switch in addition to the inverter and charger, it is an ideal inverter for the areas of motorhomes, boats or yachts and the grid-connected area of uninterruptible power supply in the event of grid fluctuations or power outages. Also for use in grid-connected self-consumption systems that only draw power from the utility when the battery power is no longer sufficient or as a usv solution in which the Multiplus step in when the power from the grid operator suddenly fails and thus provide an uninterrupted power supply. Key features of the Multiplus 12/2000/80-32 1600W continuous power and 3500w peak power, for 12v battery voltage Device combination of inverter with transfer switch and 80a battery charger delivers purest 230v sine wave voltage and a clean 50Hz frequency VE.Bus communication port provides extensive networking, system integration, configuration and control of Multiplus devices from Victron supports three-phase operation (3 identical units of the same model required) Multiplus units can be connected in parallel, up to 6 units can be connected in parallel, significantly increasing system performance when needed PowerControl function allows working with limited generator power as well as limited shore or grid power PowerAssist function enables "power increase" of generators and shore power support in case of need can be used as usv solution for uninterruptible power supply, thanks to the integrated transfer switch can be used for grid-connected self-consumption systems that draw power from the grid operator only when battery capacity is insufficient or other programmable events have occurred compatible with numerous Victron control and display panels Massive power expansion possible Apart from the parallel connection, three units of the same model can also be configured for three-phase output. But that's not all: up to six sets of three units can be connected in parallel to achieve a huge charging capacity PowerControl - working with limited generator power, limited shore or mains power The MultiPlus is a very powerful battery charger. Therefore, it draws a lot of power from the generator or shore power. The Multi Control remote control panel can be used to set the maximum shore or generator current to be drawn. The MultiPlus then takes into account other connected AC consumers and uses only the current that is "left over" for charging. This prevents the generator or shore power connection from being overloaded. PowerAssist - "power enhancement" of generators and shore power support This function adds a new dimension to the PowerControl principle. It enables the MultiPlus to support alternative sources that are too weak. Load peaks often only occur for a limited period of time. In such a case, the MultiPlus ensures that shore power or generator output that is too weak is immediately compensated for by energy from the battery. BackUp system: alternating current even in the event of a power failure The Multiplus can be used with both non-grid-connected and grid-connected PV systems, as well as with other alternative energy systems. Software is available to detect a grid failure. Simple system configuration If settings need to be changed on a single device, this can be done in minutes using a DIP switch setting procedure. Parallel connected and three-phase systems can be configured using the VE.Bus Quick Configure and VE.Bus System Configurator software. monitoring options and on-site control Several options are available: Battery Monitor, Multi Control Panel, Ve.Net Blue Power Panel, Color Control Panel, Smartphone or Tablet (Bluetooth Smart), Laptop or Computer (usb or RS232). remote monitoring and control Victron Ethernet Remote, Victron Global Remote and the Color Control Panel enable remote maintenance and remote monitoring of the MultiPlus. In addition, system data can be stored and viewed free of charge on the vrm (Victron Remote Management) website. Remote configuration If systems with a Color Control Panel are connected to the Ethernet, they can be accessed and settings can be changed remotely. Scope of delivery: 1x Victron pmp122200000 Multiplus 12/2000/80-32 device combination consisting of 12v 2000w sine wave converter + 12v 80a battery charger + 32a transfer switch 1x user manual

The Multiplus-II 48/5000/70-50 gx is a high-end device combination from victron Energy (mpn pmp482506000) that combines classic Multiplus components with an external current sensor and integrated anti-islanding function. This extends the PowerControl and Powerassist functions to 50 a and expands the potential range of use to ess applications. The inverter module delivers a whopping 5000 w at non-linear load, or 4000 w at linear continuous load. the 48 v battery charger is also very well proportioned, with 70 a charging power, and is complemented by a 50 a transfer switch that allows lightning-fast switching between aC connections. Compared to the rest of the series, the gx variants have an integrated gx display with numerous other connection options. important features of the Multiplus-II 48/5000/70-50 gx integrated gx control unit with various communication ports PowerControl and Powerassist -increase of mains or generator power built-in anti-islanding function and connection for external current sensor (optional) can be used as a backup device in grid-connected systems for power supply in case of grid failures can be used in various ess (Energy Storage System) applications best suited for professional seafaring, yachts, vehicles and land-based, off-grid applications vE.Bus interface for parallel and three-phase operation, remote monitoring and system integration virtually unlimited power through parallel and three-phase operation can be configured on-site or remotely using vEConfigure software* technical features 5000w power at non-linear load 4000 w continuous load and 9000 w peak power for 48 v battery voltage, 50 a transfer switch and 70 a battery charger output voltage: 230 vaC, frequency: 50 Hz max. efficiency is 95%, protection class IP22 always enough power thanks to PowerControl and Powerassist a maximum mains or generator current can be set on the Multiplus-II 48/5000/70-50 gx. The MultiPlus-II then takes into account other connected AC consumers and only uses the current that is "left over" to charge the battery. This prevents the generator or mains connection from being overloaded (PowerControl function). The Powerassist function adds a new dimension to the PowerControl principle. Load peaks often only occur for a limited period of time. In such a case, the MultiPlus-II immediately compensates for insufficient generator, shore power or mains power with energy from the battery. if the load is reduced, i.e. if consumers are switched off, the energy that is then available again in sufficient quantities can be used to charge the batteries. Solar power: alternating current even in the event of a power failure The device can be used with both non-grid-connected and grid-connected pv systems, as well as with other alternative energy systems. It can be used with both solar charge controllers and grid-connected inverters. maximum flexibility thanks to two AC outputs The main output ensures uninterrupted operation. In the event of a grid failure or interruption of the shore/generator power, the MultiPlus-II takes over the supply of the connected consumers. Switching occurs so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic equipment is guaranteed. The second output supplies power only when AC power is available at the input of the MultiPlus-II. consumers that must not discharge the battery, such as a water heater, can be connected to this output. Scope of the integrated gx device A vE.Can interface This can be used to connect vE.Can devices from victron (e.g. vE.Can mppt). The port can also be reconfigured via the remote console for use with a compatible CaN-Bus Li-Ion battery. 1xUSB connection 1x Ethernet port 1x vE.Direct connection many possibilities for system expansion Settings can be changed within minutes using the vEConfigure software (requires a computer or laptop and MK3 USB interface).multiple monitoring and control options are available: Color Control gx, venus gx, Octo gx, CaNvu gx, laptop, computer, Bluetooth (with the optional vE.Bus Smart Dongle), battery monitor, Digital Multi control panel. Remote configuration and monitoring Install a Color Control gx or other gx products to connect to the Internet. Operating data can be stored and viewed free of charge on our vRM (victron Remote Management) website. If systems are connected to the Internet, they can be accessed remotely and settings can be changed. Scope of delivery: 1x victron pmp482506000 Multiplus-II 48/5000/70-50 gx 230v 1x instruction manual

The Multiplus-II 48/5000/70-50 is a high-end device combination from victron Energy (mpn pmp482505010) that combines classic Multiplus components with an external current sensor and integrated anti-islanding function. This extends the PowerControl and Powerassist functions to 100 a and expands the potential range of use to ess applications. The inverter module delivers a whopping 5000 w at non-linear load, or 4000 w at linear continuous load. the 48 v battery charger is also very well proportioned, with 70 a charging power, and is complemented by a 50 a transfer switch that allows lightning-fast switching between aC connections important features of the Multiplus-II 48/5000/70-50 PowerControl and Powerassist -increase in mains or generator output built-in anti-islanding function and connection possibility for external current sensor (optional) can be used as a backup device in grid-connected systems for power supply in case of grid failures can be used in various ess (Energy Storage System) applications best suited for professional seafaring, yachts, vehicles and land-based, off-grid applications vE.Bus interface for parallel and three-phase operation, remote monitoring and system integration virtually unlimited power through parallel and three-phase operation can be configured on-site or remotely using vEConfigure software* technical features 5000 w power at non-linear load 4000 w continuous load and 9000 w peak power for 48 v battery voltage, 50 a transfer switch and 70 a battery charger output voltage: 230 vaC, frequency: 50 Hz max. efficiency is 95%, protection class IP22 always enough power thanks to PowerControl and Powerassist a maximum mains or generator current can be set on the Multiplus-II 48/5000/70-50. The MultiPlus-II then takes into account other connected AC consumers and only uses the current that is "left over" to charge the battery. This prevents the generator or mains connection from being overloaded (PowerControl function). The Powerassist function adds a new dimension to the PowerControl principle. Load peaks often only occur for a limited period of time. In such a case, the MultiPlus-II immediately compensates for insufficient generator, shore power or mains power with energy from the battery. if the load is reduced, i.e. if consumers are switched off, the energy that is then available again in sufficient quantities can be used to charge the batteries Solar power: alternating current even in the event of a power failure The device can be used with both non-grid-connected and grid-connected pv systems, as well as with other alternative energy systems. It can be used with both solar charge controllers and grid-connected inverters. maximum flexibility thanks to two AC outputs The main output ensures uninterrupted operation. In the event of a grid failure or interruption of the shore/generator power, the MultiPlus-II takes over the supply of the connected consumers. Switching occurs so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic equipment is guaranteed. The second output supplies power only when AC power is available at the input of the MultiPlus-II. consumers that must not discharge the battery, such as a water heater, can be connected to this output. many possibilities for system expansion Settings can be changed in minutes using the vEConfigure software (which requires a computer or laptop and an MK3 USB interface).several monitoring and control options are available: Color Control gx, venus gx, Octo gx, CaNvu gx, laptop, computer, Bluetooth (with the optional vE.Bus Smart Dongle), battery monitor, Digital Multi control panel Remote configuration and monitoring Install a Color Control gx or other gx products to connect to the Internet. Operating data can be stored and viewed free of charge on our vRM (victron Remote Management) website. If systems are connected to the Internet, they can be accessed remotely and settings can be changed. Scope of delivery: 1x victron pmp482505010 Multiplus-II 48/5000/70-50a 1x user manual