EcoFlow PowerKit 2kWh Independence Kit

The EcoFlow Power Kit with the 2kWh battery can be combined in a wide variety of ways to generate energy for carefree, off-grid living and motorhome travel - in a small space. The modular energy system is the world's first compact energy solution designed specifically for small homes and motorhomes. These customizable plug and play power systems are now simpler than ever and can be adapted to your individual requirements.

About the EcoFlow power kits

• 4 charging methods
• 4 different inputs for motorhomes (solar power input, vehicle generator input, shore power input, smart generator input)
• 2 different inputs for off-grid living (solar power input, smart generator input)
• Intelligent controls
• Compact and integrated design
• Easy to assemble
• Space saving
• 48v, a safe, smaller solution

The 2 kWh power kits are available in 3 different sets:

• Get Set Kit:
  • 2kWh battery
  • Power Hub
  • Cable package
• Prepared Kit:
  • 2kWh battery
  • Power Hub
  • AC/dc distribution box
  • Cable package
• Independence Kit eu:
  • 2kWh battery
  • Power Hub
  • AC/dc distribution box
  • Console
  • Cable package

2kWh battery module

The 2kWh battery from EcoFlow is equipped with the latest LiFePO4 cell technology and offers you high cycle stability and longevity. The modular, stackable concept enables flexible use of up to 4 kWh and is easy to install. It also boasts a nominal voltage of 51.2v and a capacity of 2048Wh. The built-in battery management system (bms) and the integrated car heating system ensure that the battery runs safely and can be charged quickly even at low temperatures. In addition to the 2kWh variant listed here, the 5kWh-Variant can also be purchased.

About the 2kWh LFP battery

• LiFePO4 technology
• Modular and stackable
• Extended bms for battery protection
• Intelligent control with the EcoFlow app
• Battery heater
• Safe use with hot-swap function
• Expandable up to 4kWh

Automatic heating

Heating during charging: The battery is equipped with a charging heating function that enables operation at low temperatures. The charging heater is automatically activated when the ambient temperature is below 0°C and the battery is in charging mode. The heater requires a charging power of >250W. As soon as the internal temperature of the battery rises above 5°C, the charging process can begin. When the internal temperature reaches over 10°C, the charging heater is deactivated and the charging process continues.
Heating up when discharging: The capacity can be significantly reduced if the battery is discharged at high power at a low temperature. To counteract this problem, it is equipped with a discharge heating function. This function can be activated manually via the EcoFlow app. If the internal temperature of the battery is below 0°C and the state of charge of the battery is >70%, you can activate the discharge heater in the app. The function is automatically deactivated if the state of charge is <50% or the internal temperature of the battery is above 10°C.

Technical data

• Capacity: 2048 Wh (40 Ah)
• Nominal voltage: 51.2 V
• Charge cut-off voltage: 57.6 V
• Discharge cut-off voltage: 40 V
• Max. Charging current: 32 A
• Max. Discharge current: 80 A
• Dimensions: 348 x 198 x 285 mm
• Weight: 17.1 kg
• Storage temperature: -20°C to 50°C
• Operating temperature: -20°C to 50°C
• Cycles: 3000 to 80% capacity
• Protection class: IP54

Power Hub

The Power Hub from EcoFlow is equipped with a 3600w AC output and includes two MPPT solar charge controllers, a dc/dc battery charger with mppt, an inverter charger and a dc-dc step-down converter. With all these components, you are ideally equipped to supply your tiny house or camper with energy. Its intelligent MPPT algorithm enables fast tracking and optimum solar yield. To protect the generator, the battery charger automatically adjusts the current.

About the Power Hub

• Outstanding MPPT algorithm
• Bluetooth, wifi, mobile app
• Various operating modes
• X-Boost (enables an AC output of 5000W to be achieved)
• X-Stream (fast charging with 3000w AC input)
• Compatible
• Automatic adjustments
• Efficiency and protection
• Easy to use and install

X-Boost function

X-Boost technology allows this product to supply an appliance with a maximum power of 5200w (for heaters only) while the rated output power remains at 3600w to prevent operational failure due to overload protection. The function is not available if the AC output is operated in bypass mode. The function is also not suitable for all appliances. It is particularly suitable for heating and motorized appliances, but not for products with voltage protection, such as precision instruments.

Operating modes

Bypass mode: When the appliance is connected to an external AC source and the AC output is switched on, the system switches to bypass mode. The AC output is powered by the external AC supply while the LFP battery is charged by the external AC supply. If no external AC source is available, this product will automatically switch to inverter mode. In this mode, the AC output is reactivated for power supply within only 30ms.
Inverter mode: If no external AC power source is available, the inverter provides AC power via current output.
Standby mode: If both the AC output and the dc output of the device are permanently deactivated and no charging input is made within 20 seconds, the device switches to standby mode to reduce energy consumption. It can be reactivated by pressing the dc out or AC out button.

Technical data

• AC main output
  • Pure sine wave voltage
  • Power: 3600 W
  • Voltage: 230 V
  • Frequency: 50 HZ
• AC standard output
  • Voltage: 230 V
  • Current: 10 A
• Direct current output
  • 13.6 v, 70 a, max. power 1000W
  • or
  • 26.4 v, 60 a, max. power 1600W
• Maximum power supported by X-Boost
  • 5200 W
• AC input voltage: 220-240 V
• Dimensions: 30 x 48 x 14cm
• Weight: 14kg
• Storage temperature: -25°C to 60°C
• Operating temperature: -25°C to 60°C

AC/dc distribution box

The intelligent Distribution box from EcoFlow simplifies installation and improves the safety and clarity of power distribution with an easy-to-connect plug and clear LED indicators. It also supports two installation methods. One is inline installation and the other is direct wall mounting. With an easy-to-wire plug and clear LED indicators, the intelligent distribution box offers simple set-up and makes setting up power distribution safer and clearer.

Technical data

• AC input: 220-240v, 50Hz
• Maximum input current: 30A
• dc output: 10-30v dc
• Maximum input current 70A
• Weight: 2,6kg
• Dimensions: 354 x 210 x 98mm
• Operating temperature: -25°C to 60°C
• Storage temperature: -25°C to 60°C

Console

With the Power Kit Console from EcoFlow, you can manage your entire power supply system via the touchscreen, which is installed either in your motorhome or in your own property. Monitor your own consumption in real time, adjust the settings and keep an eye on your energy requirements. To protect the system and improve its functionality, update the firmware regularly.

Software functions

• Display of the battery level
• Remaining charging and discharging time
• Input and output power
• Setting the AC/dc output switch
• Setting the dc output voltage
• Setting the dc output data
• Setting the AC input
• Setting the maximum discharge level
• Setting the minimum charge level

Functions of the USB port

USB-C: Used for a software upgrade or emergency power supply (not required)
USB-A: Supports a 5V/1A power output that can power some USB peripherals, such as MiFi modules. (MiFi = mobile WiFi, mobile hotspot)

Technical data

• dc input/RJ45: 12V/1a, max. 12W
• dc input/USB-C: 5V/2a, max. 10W
• dc output/USB-A: 5V/1a, max. 5W
• Weight: 450g
• Dimensions: 204.5 x 113.3 x 22.3 mm
• Screen size: 154.2 x 85.9 mm
• Screen resolution: 1024 (h) x 600 (V)
• Operating temperature range: -20°C - +50°C
• Touch operation: Supported